Nexcom NPT 1550 Bedienungsanleitung

User ManualVersion V1.0 Feb 2012NPT-1550

3 No. Description 1 DC 12V IN 2 Cash Drawer Port 3 USB (x4) 4 LAN (10/100/1000) 5 COM(x4) 6 2nd VGA 7 DC 12V OUT 8 2.5 HDD 9 Parallel port 10

4 3. System Assembly & Disassembly 3-1 Replace the HDD a. Unfasten the screws (x2) to remove the HDD cover. b. Disconnect the HDD Cable a

5 3-2 Replace the Motherboard To replace the motherboard, please follow the below steps: (1) Disconnect the HDD cable from the motherboard (Chapter 3

6 3-3 Replace the Inverter Board & Touch Board: 3-3-1 Replace the Inverter Board a. The location of Inverter board on the LCD sheet metal bracke

7 3-3 Install VFD & MSR (Optional): 3-4-1 VFD install: a. Unfasten the screws. b. Install VFD Module on the rear cover. c. Tighten the screw

8 4. Specification Model Name NPT-1550 Motherboard NP-D5250 Processor Intel® Atom D525 Dual-Core Processor, 1.8GHz, 1M L2 Cache Chipset Inte

9 MSR ISO 3 Tracks MSR (USB or PS/2) Customer Display 2 x 20 VFD customer display 2nd Display 15" LCD monitor Certificate EMC & Safet

10 5. Jumper Settings 5-1 NP-D5250 Motherboard Layout

11 5-2 Connectors DescriptionConnector Purpose Connector Purpose CN1 COM5 CN2 LVDS CON 24bit CN3 COM6 CN4 LVDS CON 18bit CN5 MINI PCI-E CN

12 5-3 Jumper Settings Panel Power selection:JP1 Function JP1 (1-2) (2-3) ◎3V 5V ◎Default setting 1-2 short. CMOS CLEAR SIGNAL: JP2 Function

1 Copyright 2012 All Rights Reserved Manual Version 1.1 Model Number: NPT-1550 The information contained in this document is subject to change witho

13 5-4 Install a Cash Drawer You can install a cash drawer through the cash drawer port. Please verify the pin assignment before installation. Pin

14 6. BIOS Settings This chapter explains how to use the BIOS Setup program for the NPT-1550. The current BIOS setup pictures in the chapter are

15 not exactly match the items of your BIOS version. 6-3 Main Features Use this menu for basic system configuration.

16 6-4 Advanced Features Use this menu to set the Advanced Features available on the system. IDE Configuration This section is used to configure t

17 IDE Configuration This section is used to configure the IDE drives. Configure SATA As IDE: This option configures the Serial ATA drives a

18 USB Configuration This section is used to configure USB devices. Legacy USB Support Due to the limited space of the BIOS ROM, the support for leg

19 ACPI Configuration This section is used to configure the Advanced ACPI configuration. Suspend mode Sets the ACPI Standby State when system goes

20 MPS Configuration This section is used to configure the MPS configuration MPS Revision Selects the MPS revision used by the system. Default:[1.

21 Parallel Port Mode This field is used to select normal, ECP or EPP mode of the parallel port. Default: [Normal] Parallel Port IRQ This field is u

22 Hardware Health Configuration This section is used to configure the hardware monitoring events such as the temperature, fan speed and voltages.

2 Safety IMPORTANT SAFETY INSTRUCTIONS 1. To disconnect the machine from the electrical power supply, turn off the power switch and remove the power

23 6-5 Boot Settings This section is used to configure settings during system boot. Boot Settings Configuration This section is used to configur

24 Boot Settings Configuration This section is used to configure settings during system boot. Quick Boot When Enabled, the BIOS will shorten or sk

25 Hit ‘DEL’ Message Display When enabled, the system displays the “Press DEL to run Setup” message during POST. Default:[Enabled] Boot Device Prior

26 Hard Disk Drives This section is used to select the boot priority sequence of the hard disk drives. Removable Drives This section is used to co

27 6-6 Chipset This section is used to configure the system based on the specific features of the chipset. North Bridge Chipset Configuration In

28 Selects the amount of system memory used by the internal graphics device. DVMT Mode Select Selects the DVMT mode. Default:[DVMT Mode] DVMT

29 USB 2.0 Controller This field is used to enable or disable the Enhanced Host Controller Inter-face controller. HDA Controller Enables or disa

30 6-7 PCIPnP This section is used to configure settings for PCI/PnP device. Plug & Play O/S Yes: Configures Plug and Play (PnP) devices tha

31 6-8 Security Settings Change Supervisor Password This field is used to set or change the supervisor password. To set a new password: 1. Sel

32 6-9 Exit Options Save Changes and Exit: To save the changes and exit the Setup utility, select this field then press <Enter>. A dialog bo

3 CE MARK . This device complies with the requirements of the EEC directive 2004/108/EC with regard to “Electromagnetic compatibility” and 2006

33 To load failsafe default values from the BIOS ROM, select this field then press <Enter>. A dialog box will appear. Confirm by selecting OK.

34 Appendix Drivers Installation: The shipping package includes a Driver CD. You can find every individual driver and utility that enables you to

4 and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

5 Revision History Changes to the original user manual are listed below: Version Date Description 1.0 Feb. 2012  Initial release

6 Table of Contents 1. Package Checklist……………... 1 1-1 Standard items…………………………………

1 1. Package Checklist 1-1 Standard items a. System b. power adapter 1-2 Optional items a. Second Display b. MSR c. VFD d. driver

2 2. System View No. Description 8 VFD (OPTION) 9 System Box (Inside with Motherboard) 10 Vesa Cover 11 Cables outlet No. Description 1 Tou